✅ Enable Manual Fan Control= ipmitool -I lanplus -H ipaddress -U username -P password raw 0x30 0x30 0x01 0x00
✅ Disable Manual Fan Control= ipmitool … raw 0x30 0x30 0x01 0x01
✅ 3rd Party PCIe Response State (Fast fan speed when no therm sensors on PCIe card)= ipmitool … raw 0x30 0xce 0x01 0x16 0x05 0x00 0x00 0x00 Result1= … 00 00 00 (Enabled) Result2= … 01 00 00 (Disabled)
✅ Enable 3rd Party PCIe Response= ipmitool … raw 0x30 0xce 0x00 0x16 0x05 0x00 0x00 0x00 0x05 0x00 0x00 0x00 0x00
✅ Disable 3rd Party PCIe Response= ipmitool … raw 0x30 0xce 0x00 0x16 0x05 0x00 0x00 0x00 0x05 0x00 0x01 0x00 0x00
✅ Set All Fans (0xff) to % (??) Speed (in Hexadecimal)= ipmitool … raw 0x30 0x30 0x02 0xff 0x??
✅ Set All Fans (0xff) to 50% (0x32)= ipmitool … raw 0x30 0x30 0x02 0xff 0x32
🚩System fan #’s vary per chassis. Fan1 starts on the left side behind the Dell logo and can go up to 7 fans to the right side behind the Intel badge. The IPMI fan numbers are NOT the same as the Fan# labels on the chassis. Fan1=0x00, Fan2=0x01, Fan3=0x02, Fan4=0x03, Fan5=0x04, ect.🚩
✅ Set Fan1 (0x00) to 30% (0x1E)= ipmitool … raw 0x30 0x30 0x02 0x00 0x1E
✅ Set Fan2 (0x01) to 30% (0x1E)= ipmitool … raw 0x30 0x30 0x02 0x01 0x1E
✅ Set Fan3 (0x02) to 30% (0x1E) ipmitool … raw 0x30 0x30 0x02 0x02 0x1E
✅ Percentages to Hexadecimal & Fan Speed (R720 example)
10% = 0xA
11% = 0xB
12% = 0xC
13% = 0xD
14% = 0xE
15% = 0xF
16% = 0x10 (~3,300 RPM)
17% = 0x11
18% = 0x12
19% = 0x13
20% = 0x14
21% = 0x15 (~4,000 RPM)
22% = 0x16
23% = 0x17
24% = 0x18
25% = 0x19
26% = 0x1A
27% = 0x1B
28% = 0x1C (~5,000 RPM)
29% = 0x1D
30% = 0x1E
31% = 0x1F
32% = 0x20
33% = 0x21
34% = 0x22
35% = 0x23 (~6,000 RPM)
36% = 0x24
37% = 0x25
38% = 0x26
39% = 0x27 (~6,500 RPM)
40% = 0x28
41% = 0x29
42% = 0x2A
43% = 0x2B
44% = 0x2C
45% = 0x2D (~7,300 RPM)
46% = 0x2E
47% = 0x2F
48% = 0x30
49% = 0x31 5
0% = 0x32 (~8,000 RPM)
51% = 0x33
52% = 0x34
53% = 0x35
54% = 0x36
55% = 0x37
56% = 0x38
57% = 0x39
58% = 0x3A
59% = 0x3B
60% = 0x3C (~9,400 RPM)
61% = 0x3D
62% = 0x3E
63% = 0x3F
64% = 0x40
65% = 0x41
66% = 0x42
67% = 0x43
68% = 0x44
69% = 0x45
70% = 0x46 (~10,800 RPM)
71% = 0x47
72% = 0x48
73% = 0x49
74% = 0x4A
75% = 0x4B
76% = 0x4C
77% = 0x4D
78% = 0x4E
79% = 0x4F
80% = 0x50 (~12,100 RPM)
81% = 0x51
82% = 0x52
83% = 0x53
84% = 0x54
85% = 0x55
86% = 0x56
87% = 0x57
88% = 0x58
89% = 0x59
90% = 0x5A (~13,300 RPM)
91% = 0x5B
92% = 0x5C
93% = 0x5D
94% = 0x5E
95% = 0x5F
96% = 0x60
97% = 0x61
98% = 0x62
99% = 0x63
100% = 0x64 (15,000 RPM)
✅ Report Temperatures ipmitool … sdr type temperature
✅ Report Only Temp, Volt & Fan Sensors= ipmitool … sdr elist full
✅ Report Power Supply Output ipmitool … sdr type ‘Power Supply’
✅ Displays Energy Consumption ipmitool … delloem powermonitor
Source : https://www.youtube.com/watch?v=KamY5zMpXKI
